$32.56
$52.1
The LF-PP 10″ x 2-1/2″ sediment melt-blown filter is a polypropylene depth water filter designed to trap common particulates, including sand, silt, dirt, and rust. It is a popular prefilter choice for whole house filtration, under-sink filtration, and reverse osmosis systems because it helps protect downstream carbon cartridges, membranes, valves, and fixtures from sediment buildup. Comes in 0.5, 1, 5, 10, 20, or 50 microns Confirm length and diameter match your housing Benefits and Features of the LF-PP 10″ x 2-1/2″ Sediment Melt-Blown Filter Helps reduce visible sediment like sand, silt, dirt, and rust Depth filtration design, built to capture particles throughout the media, not only on the surface Works as a first-stage prefilter to extend the life of carbon filters and RO membranes Fits many standard 10-inch filter housings Industry-standard size 10″ × 2.5″ sediment cartridge Gradient density, multi-layered Larger particles are trapped in the outer layers, and smaller particles penetrate deeper. Greater dirt-holding ability and longer life than non-layered cartridges. Thermally bonded polypropylene microfibers for purity and chemical compatibility Contains no binders, agents, solvents, antistatic materials, or wetting agents Meets FDA requirements for food and beverage contact No leachable or extractable to contaminate No surface binders to reduce flow and increase change-out frequency Cartridges are individually shrink-wrapped Micron rating is molded into the cartridge Available in a wide range of lengths and micron ratings Common Uses Prefilter for reverse osmosis systems Whole house sediment stage ahead of carbon tanks or backwashing filters Under-sink systems where sediment is affecting taste, flow, or cartridge life Well water applications where particulate is present, after a proper water test Whole house sediment filtration Reverse osmosis prefiltration Food and beverages Oil and gas Fine chemicals Electronics Metal finishing Pulp and paper What to Check Before Ordering Cartridge length, standard 10-inch format Micron rating required for your application, choose finer microns for smaller particles, choose higher microns if you want less pressure drop Housing compatibility, confirm diameter and end style match your existing setup Replacement Guidance: LF-PP 10″ x 2-1/2″ Sediment Melt-Blown Filter Replace when the flow drops, the pressure drop increases, or the cartridge shows visible loading Replacement frequency depends on water quality and usage; high sediment water will require more frequent changes If you are using this as an RO prefilter, replace it on the schedule recommended for your system to protect the membrane FAQs for the LF-PP 10″ x 2-1/2″ Sediment Melt-Blown Filter Q: What does a melt-blown sediment cartridge remove? A: It helps reduce particulates like sand, silt, dirt, rust, and other suspended sediment. Q: Where should this cartridge go in my filtration setup? A: It is typically used as the first stage to catch sediment before carbon filters, valves, UV, or an RO membrane. Q: Will this cartridge improve taste or odor? A: Sediment filtration mainly targets particles. For chlorine taste and odor, pair with a carbon stage. Q: How do I choose the right micron rating? A: Use finer micron ratings for smaller particles and clearer water; use higher micron ratings if you want less pressure drop or your water has heavier sediment. Q: How often should I replace it? A: Replace when the flow drops or the cartridge loads up. Frequency depends on sediment levels and household usage. Want the right micron rating picked fast? Share your water source, whether you see visible sediment, and the size of the housing you use, and you can match the correct sediment cartridge with confidence. 0.5 Micron 1 Micron 5 Micron 10 Micron 20 Micron 50 Micron 0.5 Micron Cartridge Replaces: N/A = 1 Micron Cartridge Replaces: Clack Corporation 31010988 Flow-Pro FPMB1-978 GE Hytrex GX01-10 GE Osmonics MB-01-10 (Part# 1013238) GE Purtrex PX01-10 GE Selex SXE-10 Pentek P1 (Part# 155225-43) Pentek PD-1-934 5 Micron Cartridge Replaces: Clack Corporation 31050988 Flow-Pro FPMB5-978 GE Hytrex GX05-10 GE Osmonics MB-05-10 (Part# 1013231) GE Purtrex PX05-10 GE Selex SXD-10 Pentek P5 (Part# 155014-43) Pentek PD-5-934 10 Micron Cartridge Replaces: Everpure EC110 (Part# EV953440) Flow-Pro FPMB10-978 GE Hytrex GX10-10 GE Osmonics MB-10-10 (Part# 1013241) GE Purtrex PX10-10 GE Selex SXA-10 Pentek PD-10-934 20 Micron Cartridge Replaces: Clack Corporation 31250988 (25 Micron) Flow-Pro FPMB20-978 GE Hytrex GX20-10 GE Osmonics MB-25-10 (25 Micron, Part# 1013232) GE Purtrex PX20-10 GE Selex SXC-10 Pentek P-25 (Part# 155015-43) Pentek PD-25-934 50 Micron Cartridge Replaces: Clack Corporation 31500988 Flow-Pro FPMB50-978 GE Hytrex GX50-10 GE Purtrex PX50-10 Pentek PD-50-934
Melt Blown Cartridges
